Single-Output and Dual-Output Power Supplies up to 400W
Convenient performance for your applications in the field of:
- Research / development
- Laboratory / testing / experiments
- Production / test bays
- Quality assurance
- Service / training
400 W in compact design
The single-output and dual-output power supplies from the TOE 8950 range have an extremely compact design. As a result of the high efficiency of all units, the complete output power of 400 W is available without problem over wide voltage and current ranges at the front via safety sockets and at the rear via a screw-type terminal block.
Power supplies with autoranging can output their rated power over a wide and stepless range of voltage and current combinations.
Autoranging power supplies from TOELLNER have a significantly larger operating range than standard power supplies with the same output power.
Adjustment using incremental spinwheels
The output values are adjusted with a selectable resolution using wear-free incremental spinwheels, guaranteeing reliable and precise setting of all output parameters and operating functions even after many years of use.
The set and measured values for voltage, current and power as well as the menu control functions are output on a 2-row LCD with 20 characters/row.
Highest degree of safety
is guaranteed for your applications by comprehensive protective measures: adjustable overvoltage protection, limit function, fast power OFF switching, polarity reversal protection, resistance to reverse current, various internal electronic monitoring functions.
Innovative sensing circuit
An innovative sensing circuit not only keeps the power supply to your load extremely constant, it even protects sensitive loads if there is a break in the sensor line. The sensing inputs are available at the rear.
Adjustable output power
The possibility for directly setting the power is a further exceptional feature of this series. The output power of 400 W with single-output power supplies or 2 x 200 W with dual-output power supplies can then be reduced down to 5 % of the maximum output power.
With dual-output power supplies, automatic tracking permits control of the output voltage of part 2 as a function (0 – 100 %) of part 1 with retention of all control properties.
Digital and analog control interfaces
Digital: RS 232 / GPIB / USB / LAN
RS 232 and GPIB/USB/LAN (optional) interfaces with the following scope of functions are available for communication between PC and power supply:
- Adjustment of output values: voltage, current and power
- OVP and limit adjustment, autocal function, display, store and recall settings
- Switching on/off of output voltage
- Reading of actual values as well as warning/fault states
The command syntax complies with the IEEE 488.2 standard. Standardized SCPI commands are processed.
Fast analog control
The power supplies can be controlled in analog mode; i.e. the output voltage and current can be adjusted independent of one another using externally applied control voltages.
Short adjustment times for the output voltage are implemented using balanced circuitry.
It is therefore possible to generate powerful and fast output signals without problem; up to approx. 700 Hz at 2 Vpp.
By interrupting the interlock circuit, e.g. by an external emergency stop switch, the power supply output becomes deenergized directly.
A convenient feature is the output switchoff function which at standby permits immediate reduction of the voltage and current values to 0 V and 0 A. When the output key is activated, the set or programmed values for voltage and current are present immediately. The switchover can be carried out manually, via a remote control command from the PC, via an external TTL signal1) or via an external switching contact1).
1) Interlock or inhibit option required
The power supplies are equipped with a self-calibration function protected by a ”security code”. This function can be manually executed from a menu or also remote-controlled.
Price and performance
The exceptional specifications, extraordinary features, and best possible processing quality provide the power supplies of the TOE 8950 series with an excellent price/performance ratio.is.
- Automatic setting to the existing line voltage: 115 V or 230 V, 47 to 63 Hz
- RS 232 and analog interfaces included as standard
- USB, LAN, and GPIB interfaces optional
- Outputs at front and rear as standard
- On/off switching of the outputsge
- ½ 19“ weight, 2 HU design parallel installation possible
- Free LabView™ driver
- Can be used as constant voltage, constant current and constant power source (CV/CC/CP)
TOE 8952 (switching)
Data Sheet & Downloads